114 lines
2.3 KiB
YAML
114 lines
2.3 KiB
YAML
output:
|
|
- platform: gpio
|
|
pin: GPIO10
|
|
id: sensor_vcc_pin
|
|
|
|
switch:
|
|
- platform: output
|
|
output: sensor_vcc_pin
|
|
id: sensor_power
|
|
# Zorgt dat de pin bij elke boot (ook na sleep) standaard UIT staat
|
|
# totdat we hem expliciet aanzetten.
|
|
restore_mode: ALWAYS_OFF
|
|
|
|
esphome:
|
|
name: xiao-esp32c3-light-sensor
|
|
friendly_name: XIAO ESP32C3 Light Sensor
|
|
platformio_options:
|
|
board_build.f_flash: 40000000L
|
|
board_build.flash_mode: dio
|
|
board_build.flash_size: 4MB
|
|
on_boot:
|
|
priority: 900
|
|
then:
|
|
- switch.turn_on: sensor_power
|
|
- delay: 500ms # Iets langere delay voor stabiliteit van de sensoren
|
|
|
|
esp32:
|
|
variant: ESP32C3
|
|
board: esp32-c3-devkitm-1
|
|
framework:
|
|
type: esp-idf
|
|
|
|
logger:
|
|
level: DEBUG
|
|
|
|
api:
|
|
encryption:
|
|
key: "IMbpaUOgYJWv7CbCDwNjkhPQYdDylPqulrXvHS5BOKg="
|
|
|
|
ota:
|
|
- platform: esphome
|
|
password: "68124e613de22b373413d37452777c49"
|
|
|
|
safe_mode:
|
|
boot_is_good_after: 5s
|
|
|
|
|
|
wifi:
|
|
ssid: !secret wifi_ssid
|
|
password: !secret wifi_password
|
|
ap:
|
|
ssid: "Xiao-Esp32C3-Light-Sensor"
|
|
password: "nNaTBzEaDn5g"
|
|
|
|
captive_portal:
|
|
|
|
i2c:
|
|
sda: GPIO6
|
|
scl: GPIO7
|
|
scan: true
|
|
|
|
deep_sleep:
|
|
id: deep_sleep_1
|
|
sleep_duration: 10min
|
|
# De ESP blijft 20 seconden wakker om te verbinden en te meten, daarna MOET hij slapen
|
|
run_duration: 20s
|
|
# Belangrijk: setup_priority zorgt dat hij ook gaat slapen als WiFi faalt
|
|
setup_priority: -100
|
|
|
|
time:
|
|
- platform: homeassistant
|
|
id: esptime
|
|
on_time:
|
|
- hours: 23
|
|
minutes: 0
|
|
seconds: 0
|
|
then:
|
|
- deep_sleep.enter:
|
|
id: deep_sleep_1
|
|
until: "09:00:00"
|
|
time_id: esptime
|
|
|
|
sensor:
|
|
- platform: adc
|
|
pin: GPIO2
|
|
name: "Battery Level"
|
|
unit_of_measurement: "%"
|
|
# Update interval korter dan run_duration zodat hij zeker 1x meet
|
|
update_interval: 10s
|
|
attenuation: 12db
|
|
filters:
|
|
- multiply: 2.0
|
|
- calibrate_linear:
|
|
- 3.0 -> 0
|
|
- 4.2 -> 100
|
|
- clamp:
|
|
min_value: 0
|
|
max_value: 100
|
|
|
|
- platform: bh1750
|
|
name: "Lux"
|
|
address: 0x23
|
|
update_interval: 10s
|
|
|
|
- platform: adc
|
|
pin: GPIO3
|
|
name: "Soil moisture"
|
|
unit_of_measurement: "%"
|
|
update_interval: 10s
|
|
attenuation: 12db
|
|
filters:
|
|
- calibrate_linear:
|
|
- 2.5 -> 0.0
|
|
- 1.2 -> 100.0 |